Tested Material Used To 352-001 Test Engine Exam Questions in here [Oct-2021]
Penetration testers simulate 352-001 exam PDF
NEW QUESTION 114
What are two design advantages to using virtual port channel? (Choose two.)
- A. ability to use Spanning Tree Protocol blocked ports to forward traffic
- B. enhanced ability to recover from Spanning Tree Protocol changes
- C. reduced Spanning Tree Protocol convergence time
- D. enhanced system availability through multiple systems
- E. loop management without use of Spanning Tree Protocol
Answer: D,E
NEW QUESTION 115
Which two options are characteristics of firewall transparent mode operations in a firewall solution design?
(Choose two.)
- A. Changes in the existing IP addressing and subnets are required.
- B. OSPF adjacencies can be established through the firewall.
- C. The firewall acts like a router hop in the network.
- D. The firewall can participate actively on spanning tree.
- E. Multicast traffic can traverse the firewall.
Answer: B,E
NEW QUESTION 116
A large enterprise company is redesigning their WAN infrastructure and has these design requirements:
The Frame Relay WAN infrastructure will be replaced with an MPLS VPN service.
BGP is the PE-CE routing protocol adopted for this scenario.
There are 3000 routes in the routing database of the distribution routers.
All 3000 routes will be advertised from the access routers through the MPLS network.
The service provider that provides this MPLS VPN service supports only 1000 prefixes per VRF.
Which two design solutions ensure that the enterprise access routers reach all devices in this enterprise network? (Choose two.)
- A. Configure the access routers to send a default route to the MPLS network
- B. Use prefix lists on the distribution routers to control which routes are sent to the MPLS network
- C. Summarize the routes on the MPLS WAN interfaces of the distribution routers
- D. Configure null routes and aggregate routes for the prefixes in your network on the distribution routers
- E. Configure the distribution routers to send a default route to the MPLS network
Answer: C,D
NEW QUESTION 117
You work as a network designer for a company that is replacing their Frame Relay WAN with an MPLS VPN service, where the PE-to-CE routing protocol is BGP. The company has 3000 routes in their distribution routers, and they would like to advertise their access routers through the MPLS network. Their service provider, however, only supports 1000 prefixes per VRF. Which two design solutions can be applied to ensure that your access routers will be able to reach all devices in your network? (Choose two.)
- A. Configure the access routers to send a default route to the MPLS network
- B. Configure the distribution routers to send a default route to the MPLS network
- C. Use prefix lists on the distribution routers to control which routes are sent to MPLS network
- D. Summarize the routes on MPLS WAN interfaces of the distribution routers
- E. Configure null routes and aggregate routes for the prefixes in your network on the distribution routers
Answer: B,D
NEW QUESTION 118
Refer to the exhibit.
You must ensure that both core A and core B devices have only the minimum information required for reaching the spoke routers yet maintain full reachability during network failures.
Which of the following design solutions accomplishes these requirements?
- A. Route summarization, with specific route leaking on hubs A and B
- B. Route summarization, with GRE tunnel on hubs A and B
- C. Implement ODR for hub-to-spoke routing.
- D. Implement PfR enhancements on hubs A and B.
Answer: B
NEW QUESTION 119
Refer to the exhibit.
Service Provider A and Service Provider B have agreed to a strategic interconnect relationship that will allow them access into each other's geographies by using an inter-AS eBGP VPNv4 multihop between route reflectors. Which two options will accomplish this scenario? (Choose two.)
- A. RR 1 and RR 2 peer using multihop eBGP IPv4 to exchange prefixes.
- B. An LSP is formed between ASBR 1 and ASBR 2 using eBGP VPNv4.
- C. RR 1 and RR 2 peer using multihop eBGP VPNv4 to exchange prefixes.
- D. ASBR 1 and ASBR 2 act as inline route reflectors that set themselves as the next-hop.
- E. An LSP is formed between ASBR 1 and ASBR 2 using eBGP IPv4.
Answer: C,E
NEW QUESTION 120
Voice traffic between two campus enterprise networks is growing. The network designers decide to add a second 10-Mb Metro Ethernet service parallel to their original 10-Mb service in order to provide more bandwidth and diversity. The QoS profile will be the same on the new 10-Mb service due to the voice stability on the first Metro Ethernet link. When the second link is added to the OSPF domain, which traffic design consideration would have the most impact on the voice traffic when both links are active?
- A. per-source IP address basis
- B. per-flow basis
- C. per-packet basis
- D. per-destination IP address basis
Answer: C
NEW QUESTION 121
How should multiple OSPF areas be designed when deployed on a classic three-layer
(core/distribution/access) network hierarchy?
- A. The OSPF flooding domain boundary should be within the distribution layer.
- B. The OSPF flooding domain boundary should be at the edge of the core layer.
- C. OSPF flooding domain boundaries should be placed with route aggregation in mind.
- D. OSPF should generally be deployed in a three-layer domain hierarchy to align with the physical three-layer hierarchy.
Answer: C
NEW QUESTION 122
You are the lead network designer for an enterprise company called ABC, and you are leading design discussions regarding IPv6 implementation into their existing network. A question is raised regarding older Layer 2 switches that exist in the network, and if any changes are required to these Layer 2 switches for successful IPv6 implementation. Which two responses should you give? (Choose two.)
- A. If IPv6 anycast deployment is planned, then make sure that Layer 2 switches support
ND snooping at Layer 2 switches. - B. If IPv6 anycast deployment is planned, then make sure that Layer 2 switches support
DHCPv6 snooping at Layer 2 switches. - C. IPv6 is transparent on Layer 2 switches, so there is no need to make any changes to the
Layer 2 switches. - D. If IPv6 multicast deployment is planned, then make sure that Layer 2 switches support
MLD snooping at Layer 2 switches. - E. If IPv6 anycast deployment is planned, then make sure that Layer 2 switches support
ICMPv6 snooping at Layer 2 switches.
Answer: C,D
NEW QUESTION 123
You are designing a WAN network solution with EIGRP based on VPLS. The interface speed is 10 Mb/s, but the access rate of the WAN connection is 256 Kb/s. What should you include in the network design, in order to avoid potential issues with EIGRP?
- A. Tag outbound EIGRP traffic and have the WAN provider add it to the priority queue.
- B. Limit traffic to theaccess rate with interface traffic shaping.
- C. Limit EIGRP traffic to the access rate with a policer.
- D. Set the interface bandwidth to match the access rate.
Answer: D
Explanation:
Explanation/Reference:
Explanation:
NEW QUESTION 124
Which three processes are part of the ITILv3 Service Operation? (Choose three.)
- A. change management
- B. event management
- C. problem management
- D. release and deployment management
- E. service-level management
- F. incident management
Answer: B,C,F
NEW QUESTION 125
A customer wants to understand the benefits of a proposed network design that utilizes
SNMPv3. Which two network threats is SNMPv3 effective against? (Choose two.)
- A. traffic analysis threats
- B. denial of service threats
- C. masquerade threats
- D. modification of information threats
Answer: C,D
NEW QUESTION 126
When a multiprotocol routing environment is designed to have several routers redistributing among the routing domains, how can routing loops be avoided?
- A. By using route tags
- B. By implementing spanning tree
- C. By activating split horizon
- D. By using the AS-path attribute
Answer: A
NEW QUESTION 127
A company is planning to connect its 30 sites with a VPLS WAN backbone. A router at each site should establish neighborships with all other routers using the OSPF routing protocol. Which three points must be considered regarding DR and BDR when different router platforms are used? (Choose three.)
- A. It is a best practice that the routers with the most powerful hardware should take the role of the DR and
BDR. - B. The role for the DR and BDR will be selected when a new OSPF router comes up.
- C. To force two routers to become a DR and a BDR, the IP OSPF priority can be set to zero at all other OSPF routers.
- D. To select the DR and BDR, the IP OSPF priority must be set to a higher value than the default value at the DR and BDR during the selection process.
- E. To select the DR and BDR, the IP OSPF priority must be set to a lower value than the default value at the DR and BDR during the selection process.
- F. If the IP OSPF priority is the same for all routers, the highest loopback IP address and router ID will decide which routers will take the DR and BDR role during the selection process.
Answer: A,C,F
NEW QUESTION 128
Drag and drop the EIGRP design considerations from the left onto the corresponding hierarchical layer characteristics on the right
Answer:
Explanation:
NEW QUESTION 129
What are three common objectives of customers using multiple cloud providers? (Choose three )
- A. security
- B. regional cloud provider access
- C. feature disparity
- D. high availability
- E. analytics
- F. bandwidth
Answer: A,B,D
NEW QUESTION 130
Which technique can be used to deploy IPv6 services in an IPv4-only routed backbone network?
- A. 6RD on CE routers and 6RD border relays at the peering locations
- B. 6PE in the backbone network
- C. dual-stack lite and NAT44 at the peering locations
- D. NAT64 at the peering locations
Answer: A
NEW QUESTION 131
......
Authentic Best resources for 352-001 Online Practice Exam: https://www.torrentvce.com/352-001-valid-vce-collection.html