Online CRE Test Brain Dump Question and Test Engine
Real ASQ CRE Exam Dumps with Correct 265 Questions and Answers
NEW QUESTION 81
A data collection, analysis, and reporting system should:
I. Permit detailed failure and failure rate analysis for varying environments, time periods, storage conditions, etc.
II. Provide distinction between items that failed and item that were wrongly removed.
III. Report data on successes as well as failures.
Response:
- A. I and III only
- B. II and III only
- C. I, II and III
- D. I only
Answer: C
NEW QUESTION 82
The use of plug-in devices improves all of the following EXCEPT:
Response:
- A. Fault isolation time.
- B. Design reliability.
- C. Interchangeability
- D. Mean time to repair.
Answer: B
NEW QUESTION 83
An air handling system has a MTBF of 8000 hours, MTBMct of 120 hours, and MMT (mean maintenance action time) of 230 hours. Determine the potential availability.
Response:
- A. 0.9852.
- B. 0.9866.
- C. 0.9721.
- D. 0.9575.
Answer: A
NEW QUESTION 84
What are the life cycle costs for a new stamping machine purchased by a metal fabrication plant?
Pertinent cost data follows:
Purchase Price = $230,000
Repair Costs = $107,000
Post Purchase Costs = $870,000
Start Up Costs = $125,000
Maintenance Costs = $420,000
Energy Costs = $325,000
Response:
- A. $2,077,000
- B. $1,100,000
- C. $787,000
- D. $1,207,000
Answer: B
NEW QUESTION 85
In a certain application, two identical transducers are used to measure the vacuum in a system. The system is considered to have failed if either of the vacuums read by the transducers varies from the standard by more than 10mm Hg.
Which of the following is the correct reliability logic block diagram for the transducer assembly?
Response:
- A. Option C
- B. Option A
- C. Option B
- D. Option D
Answer: B
NEW QUESTION 86
Which answer mathematically expresses the reliability of an active parallel system in which all component reliabilities are unequal?
Response:
- A. Rs = [RaRbRc + RaRb + RbRc + RaRc ] / [Ra + Rb + Rc]
- B. Rs = RaRbRc - (RaRb + RbRc + RaRc) + (Ra + Rb + Rc)
- C. Rs = Ra + Rb + Rc - RaRbRc
- D. Rs = [RaRbRc] / [Ra + Rb + Rc]
Answer: B
NEW QUESTION 87
Maintainability is:
Response:
- A. Performing adequate maintenance on a system.
- B. The probability of a system being restored to functional operation within a given period of time.
- C. Probability of survival of a system for a given period of time.
- D. Maintaining a machine in satisfactory working condition.
Answer: B
NEW QUESTION 88
The success of the FMEA is principally dependent on:
I. Good communication between the reliability engineer and the designer.
II. Use of the correct form and definitions.
III. Early determination of the reliability critical items.
Response:
- A. I only
- B. II only
- C. II and III only
- D. III only
Answer: A
NEW QUESTION 89
System and cost effectiveness analysis outputs:
Response:
- A. Do not guide trade-off decisions.
- B. Can be used to determine the best balance of system performance, cost and schedule.
- C. In most cases will not identify the degree to which innovations should be pursued.
- D. Will not guide preliminary design features.
Answer: B
NEW QUESTION 90
The department having the authority to sign all deviations pertaining to the design of the product is normally:
Response:
- A. Inspection
- B. Manufacturing engineering.
- C. Design engineering.
- D. Contractual
Answer: C
NEW QUESTION 91
Which of the following activities prioritizes failure modes based on probability of failure, severity, and consequences?
Response:
- A. FURPS.
- B. FRACAS.
- C. FMEA
- D. FTA
Answer: C
NEW QUESTION 92
A plastics plant operates 8 extruders producing plastic film. Production volume requirements cannot be met if less than 6 extruders are operating. There is a .30 probability that a machine stopping malfunction will occur.
What is the probability that 6 extruders can remain operating throughout the day?
Response:
- A. 0.5518
- B. 0.5783
- C. 0.4482
- D. 0.8059
Answer: A
NEW QUESTION 93
Using complete field-based data, a reliability engineer has analyzed the reliability growth of a repairable system over the last 24 months. The analysis suggests a "no growth" condition, and that finding is reported to management.
Due to a pending multimillion dollar order, management requests that a line be drawn to show growth where none actually exists. The engineer's department manager directs the engineer to comply with management request.
The system is released without improvements and the company receives the multimillion dollar order from an external customer. The customer then requests evidence of the reliability growth. Which of the following actions by the engineer would be MOST appropriat?
Response:
- A. Ask the department manager to respond to the customer's request.
- B. Arrange a meeting with the customer and discuss all past occurrences
- C. Revisit the original data and project artificial reliability growth to satisfy the customer's request.
- D. Arrange a meeting with the department manager and upper management to discuss the reliability report.
Answer: D
NEW QUESTION 94
In general, one should select the highest component parameter ratings feasible so that:
I. Failure rates may be minimized.
II. Probability of secondary failure is minimized.
III. Safety margins are offered against unforeseen transients.
Response:
- A. I and III only
- B. I and II only
- C. I, II and III
- D. I only
Answer: C
NEW QUESTION 95
The prediction technique has obviously not always been effective quantitatively. There is often a wide difference between actual reliability and predicted reliability. Nevertheless, the reliability prediction technique permits:
Response:
- A. Estimating how good the product really is.
- B. Spotlighting what has gone wrong with the program.
- C. Separating out "the vital few" from the "trivial many".
- D. Indicating which department is to blame.
Answer: C
NEW QUESTION 96
Which mathematical method provides a solution, has a time dimension and is solved numerically?
Response:
- A. None of the above.
- B. Strength and stress model.
- C. Analytic solution.
- D. Simulation model.
Answer: D
NEW QUESTION 97
Which of the following is a key element of an effective reliability growth program?
Response:
- A. A field service support organization
- B. A reliability prediction program.
- C. Field generated engineering change orders.
- D. A failure reporting analysis and corrective action system.
Answer: D
NEW QUESTION 98
Preventive maintenance programs are MOST effective when
Response:
- A. Random failure occur
- B. The hazard rate is decreasing.
- C. The hazard rate is increasing.
- D. The hazard rate is constant.
Answer: C
NEW QUESTION 99
......
Valid CRE Test Answers & ASQ CRE Exam PDF: https://www.torrentvce.com/CRE-valid-vce-collection.html
ASQ CRE Certification Real 2021 Mock Exam: https://drive.google.com/open?id=1eae6mo4epVXPOEl3ypR3RT4RBSz8z4Oi